第1个回答 2010-09-25
1. The high-pressured teflon hose module is Teflon hose module working pressure scope 0~28MPa
2. A attachment is the external screw thread connection, the B attachment connects
for the box thread 3. The hose length may need to order
according to the customer 4. If hose's both sides attach the external form not to be inconsistent, then may carry on before its attachment seal form marks
for example: GZT0A/ZJ1B-04
expressed that an end goes nonstop to 37° is an external screw thread, another end for the right angle 60° box thread attachment, the nominal size is 04 hoses.
5. has not explained the attachment material, generally uses stainless steel 1Cr18Ni9Ti, if needs to change please do explain.
6. application temperature for - 55℃~+1
第2个回答 2010-09-25
特氟隆软管总成表示方法
说明:
1. 高压聚四氟乙烯软管组件即特氟隆软管组件使用压力范围0~28MPa
2. A型接头为外螺纹连接,B型接头为内螺纹连接
3. 软管长度可根据客户需要订制
4. 如果软管的两端接头外部形式不一致,则可在其接头密封形式前进行标识
例如:GZT0A/ZJ1B-04
表示一端直通37°为外螺纹,另一端为直角60°内螺纹接头,公称通径为04的软管。
5.未说明接头材料,一般采用不锈钢 1Cr18Ni9Ti,若需要更改请说明。
6.使用温度为-55℃~+180℃,工作介质为各种气体、液体、及腐蚀性介质
7. 公称通径为4mm~25mm。
特氟隆软管总成结构组成
特氟隆软管总成由接头组件、扣压外套、聚四氟乙烯软管组成。接头组件由接头和外套螺母组成。接头外端的连接方式与航空航天标准一致,接头的另一端(与软管相连端)内部与软管之间有两道密封唇以保持连接的密封性,外部与软管的钢丝编织层扣压连接,既保证了连接的强度,又在外部起到了密封作用。接头组件与聚四氟乙烯软管采用扣压方式连接。
Teflon hose assembly representation
Description:
1. High-pressure hose assemblies PTFE Teflon hose assemblies that use the pressure range 0 ~ 28MPa
2. A type male connector for connection, B-type connector for connecting thread
3. Hose length can be customized according to customer needs
4. If the hose connection at both ends of the external form of inconsistency, you can seal in the form of its joints are identified before
For example: GZT0A/ZJ1B-04
Said one end through 37 ° for the male and the other end for the 60 ° right angle female connector, the nominal diameter of the hose 04.
5. Unspecified joint material, generally made of stainless steel 1Cr18Ni9Ti, if you need to change your instructions.
6. Temperature is -55 ℃ ~ 180 ℃, the working medium for a variety of gases, liquids, and corrosive media
7. Nominal diameter of 4mm ~ 25mm.
Teflon hose assembly structure and composition
Teflon hose assembly from the connector component, withholding coat, composed of PTFE hose. Connector component formed by the joints and coats nuts. The outer end of the connection joints and aerospace standards, the other end of connector (with the hose connected to end) between the inside and the hose to keep the connection ends and two seal lips sealed, externally with steel wire braid hose connection withheld , both to ensure the strength of the connection, but also played a role in sealing the outside. PTFE hose assemblies and fittings connected by withholding.